Video scenes shots:
Watch the video:
Other videos by this author:
 |
Introduction4e-500.wmv Posted by: freemanmfg
Video duration: 205 seconds Introduction to our DVD: Parts, Patterns, Tools, & Molds, Fourth Edition |
 |
Epoxy Fiberglass Laminating Introduction Posted by: freemanmfg
Video duration: 320 seconds Ideal for working on larger projects, a typical 'fiberglass layup' is a popular process for those who need a large, strong, and lightweight tool. |
 |
Vacuum Bagging a Composite (Carbon Fiber) Part (Preview) Posted by: freemanmfg
Video duration: 269 seconds Using the fiberglass mold created in another video, we demonstrate the vacuum bagging process by forming a carbon fiber part. |
 |
Building a Fiberglass Laminate Mold (Preview) Posted by: freemanmfg
Video duration: 272 seconds Here we apply the techniques from the video above plus some more advanced techniques to create a more complex epoxy fiberglass laminate tool. |
 |
Mold Making - Casting Thin-Walled Parts (Preview) Posted by: freemanmfg
Video duration: 142 seconds Casting thin-walled parts follows a similar process to the mass casting video above. However, this project requires important differences in venting, gating, and the use of pressure. |
 |
Updated - Mold Making - Urethane Rubber Molds Posted by: freemanmfg
Video duration: 283 seconds Urethane Rubber molds are widely used when a flexible mold material is required and a more expensive or less abrasion-resistant silicone rubber is not desired. However, their use requires careful application of release agents. |
 |
Tooling With Fiberglass Strand & Urethane Posted by: freemanmfg
Video duration: 318 seconds Ideal for working on medium-sized projects, this process is easier, faster, and more economical than the epoxy laminating system. |
 |
Updated - Simple Silicone Rubber Molds (no parting line) Posted by: freemanmfg
Video duration: 424 seconds Ideal for smaller projects (less than 12" x 12"), this is the easiest process for creating parts, patterns, tools, & molds. We demonstrate creating a silicone rubber mold and then the casting of parts with Repro, epoxy casting resins and polyurethane elastomers. |
 |
Updated - Mold Making - Surface Casting Posted by: freemanmfg
Video duration: 328 seconds Ideal for working on medium-sized projects, this process of pouring a high quality material around a lower quality core creates a highly accurate, yet economical part. |
 |
Updated - Moldmaking With Clear Silicone Rubber Posted by: freemanmfg
Video duration: 498 seconds When a project requires a complex parting line, it is often easier to pour the entire mold in one process with clear rubber, then cut your parting line. This process also saves at least a day in creating the mold. |
 |
Updated - Epoxy Paste & Fiberglass Laminating Systems Posted by: freemanmfg
Video duration: 419 seconds This process is for working on medium to large projects, this is a labor-saving process for those who need a large, strong tool in the least amount of time possible. This video also demonstrates three-part mold construction. |
 |
Updated - Glove Molding Systems Posted by: freemanmfg
Video duration: 586 seconds Ideal for working on medium and large projects, this process invloves creating a thin layer of flexible material and backing it up with a stronger, rigid material. |
 |
Updated - Mold Making Casting Complex Parts w/ parting line) Posted by: freemanmfg
Video duration: 559 seconds When mass casting a part without a flat side, you must create a two-part mold. We create a two-part silicone rubber mold with a clean parting line and then cast the part with Repro. |
 |
Updated - Making Rigid Molds With Fast-Cast Urethanes Posted by: freemanmfg
Video duration: 312 seconds Ideal for smaller models/molds with a flat side, fast-cast urethanes are widely used for their ease of use, low cost, and quick demold times. However, their use requires careful application of release agents. |
 |
Glove Molding Systems Posted by: freemanmfg
Video duration: 562 seconds Ideal for working on medium and large projects, this process invloves creating a thin layer of flexible material and backing it up with a stronger, rigid material. |
 |
The Repro Laminating System Posted by: freemanmfg
Video duration: 297 seconds Ideal for working on medium-sized projects, this process is easier, faster, and more economical than the epoxy laminating system. |
 |
Paste Laminating Systems Posted by: freemanmfg
Video duration: 385 seconds This process is for working on medium to large projects, this is a labor-saving process for those who need a large, strong tool in the least amount of time possible. This video also demonstrates three-part mold construction. |
 |
Epoxy Laminating Systems Posted by: freemanmfg
Video duration: 305 seconds Ideal for working on larger projects, a typical 'fiberglass layup' is a popular process for those who need a large, strong, and lightweight tool. |
 |
Mold Making - Surface Casting Posted by: freemanmfg
Video duration: 305 seconds Ideal for working on medium-sized projects, this process of pouring a high quality material around a lower quality core creates a highly accurate, yet economical part. |
 |
Moldmaking With Clear Silicone Rubber Posted by: freemanmfg
Video duration: 473 seconds When a project requires a complex parting line, it is often easier to pour the entire mold in one process with clear rubber, then cut your parting line. This process also saves at least a day in creating the mold. |
 |
Mold Making - Mass Casting Complex Parts (w/ parting line) Posted by: freemanmfg
Video duration: 538 seconds When mass casting a part without a flat side, you must create a two-part mold. We create a two-part silicone rubber mold with a clean parting line and then cast the part with Repro. |
 |
Simple Silicone Rubber Molds (no parting line) Posted by: freemanmfg
Video duration: 402 seconds Ideal for smaller projects (less than 12" x 12"), this is the easiest process for creating parts, patterns, tools, & molds. We demonstrate creating a silicone rubber mold and then the casting of parts with Repro, epoxy casting resins and polyurethane elastomers. |
 |
Mold Making - Urethane Rubber Molds Posted by: freemanmfg
Video duration: 261 seconds Urethane Rubber molds are widely used when a flexible mold material is required and a more expensive or less abrasion-resistant silicone rubber is not desired. However, their use requires careful application of release agents. |
 |
Mold Making - Making Rigid Molds With Fast-Cast Urethanes Posted by: freemanmfg
Video duration: 290 seconds Ideal for smaller models/molds with a flat side, fast-cast urethanes are widely used for their ease of use, low cost, and quick demold times. However, their use requires careful application of release agents. |
